Drywall Installation in Meridian, Idaho

Meridian Quality Drywall provides drywall installation in Meridian for new rooms, additions, and remodels that need gypsum hung to a straight plane. If the board is proud at a joint, run the wrong way on a lid, or screwed into foam instead of a stud, no amount of mud will hide it. Homeowners and builders call when framing is ready and the inspections have cleared.

Reach us at (208) 382-8431 with square footage, ceiling height, and whether this is a new build or a room add. We quote the hang before the first sheet goes up.

Drywall Installation Options for Meridian Properties

Horizontal 1/2-inch on 16-inch studs

Most Meridian interiors are 2x4 partitions and 2x6 exteriors at 16 inches on center. We snap lines, shim the bowed studs, and hang 1/2-inch regular board horizontally so the butt joints land on blocking. Screws dimple the face paper without tearing it. Construction adhesive on long runs cuts fastener pops after the wood dries.

Ceiling sheets run across the joists

Lids get hung perpendicular to the joists, never parallel to them. Parallel hanging on 24-inch centers sags. That sag shows as a wave after paint, especially under LED cans. We use 5/8-inch when the spacing or the span calls for it. A drywall lift keeps the sheet tight to the framing while we screw.

Moisture board and cement board rooms

Moisture-resistant green or purple board in baths and laundry. Cement board such as HardieBacker or Durock in the shower surround. Those two are not interchangeable. Tile bond coats want cement board. Paint wants moisture-resistant gypsum outside the spray.

Tall plates, trays, and bulkheads

Eagle and Hidden Springs jobs add trays, radius walls, and 10-foot plates. More cuts, more bead, more time. Production knockdown on a 12-foot foyer looks cheap in that light. Tray lids go up before the walls so sheets catch that lid.

How We Handle Drywall Installation in Meridian

1. Confirm rough-in inspections have passed. Hanging over uninspected electrical is how you tear board back out.
2. Check stud layout, bow, and joist direction. Shim before the first sheet. Mark box locations on the floor so cuts stay tight.
3. Hang ceilings first, then walls, so the wall sheets catch the ceiling edge. Start at the interior corners and work out.
4. Cut boxes tight. Outside corners get metal or vinyl bead. Inside corners get paper tape, not bead.
5. Walk the house for ringing sheets that missed a stud. Then taping starts.

Materials and Methods

We hang gypsum that meets ASTM C1396. Regular 1/2-inch on dry interiors. 5/8-inch Type X, often USG Firecode C, on garage lids and the wall between garage and dwelling. Green or purple moisture-resistant board in wet rooms. Cement board in the surround. Paper tape on fresh joints. Screws, not nails. A screw gun set so the head dimples without breaking the face paper. GA-216 is the hanging practice we work to. The garage-to-house fire separation is why Type X belongs there. Standard sheets are 4x8. Long 4x12 sheets cut joints on tall walls. We store board flat. A bowed sheet from a hot garage will telegraph through paint.

Application follows ASTM C840 as well as GA-216. Joint materials meet ASTM C475. GA-214 finish levels start after the hang. Paper tape on fresh joints. Screws, not nails. 1/2-inch interiors. 5/8-inch Type X on garage lids. USG Firecode C where the assembly is rated. Cement board in the surround. Store board flat. A bowed sheet from a hot garage telegraphs through paint.

Production houses in Paramount and Tuscany hang faster than a custom plate in Eagle because the walls are square and the lids are 8 or 9 feet. We still shim the bowed studs. A fast hang that leaves a wave is not a finished hang. Long 4x12 sheets cut joints on tall walls when we can get them up the stairs. Stairwells, two-story foyers, and 12-foot great rooms are staged as tall work, not as a bedroom hang turned on end.

We mark electrical boxes on the floor before the first sheet so the cut stays on the box, not a half inch off. Tight cuts save hours of mud. Loose cuts become a tape problem. Outside corners get bead that we plumb with a level, not by eye from the doorway. A leaning bead is a shadow after paint.

What Drywall Installation Costs in Meridian

Fixr's 2025 guide puts hang-and-finish work nationally at one dollar fifty through three dollars fifty per square foot. Angi groups typical installs from a dollar fifty to three dollars a square foot. HomeAdvisor's 2026 hanging guide lists many jobs from about 1,000 dollars to 3,254 dollars. Three things move a Meridian quote: ceiling height and trays, Type X and wet-room board, and whether the house has heat yet. We give a quote. We do not publish a price list.

A Meridian hang is a layout job as much as a screw gun job. We snap a line at 48 inches so the sheets land on a stud. We check for missing backing at towel bars, cabinets, and TV walls before the board hides the bay. Adding backing after the hang means a cut-out. Adding it now is a 2x and a handful of screws.

Board that sat in a south-facing garage in July takes a set. We reject a warped sheet rather than fight it on the wall. In January we want the house above freezing before we hang, because a frozen sheet sweats and the face paper bubbles. Those two seasons are why a calendar quote from another state does not fit this bench.

Drywall Installation Questions

Which thickness of board goes in a Meridian house?

Interior partitions usually take 1/2-inch. Lids over 24-inch joist spacing, garage ceilings, and fire assemblies take 5/8-inch Type X. Baths and laundry take moisture-resistant panels, not regular white board.

Is sheetrock the same product as gypsum board?

Yes. Sheetrock is a USG brand name. We hang gypsum that meets ASTM C1396 either way: 1/2-inch on interiors, 5/8-inch Type X where the assembly is rated.

How long does hanging take on a typical house?

A production home in south Meridian can be hung in a few days once mechanical, electrical, and plumbing inspections have cleared. Custom homes with tall walls and trays take longer because the cuts multiply.

Do you hang additions and remodels as well as new houses?

Yes. A room add, a basement finish, and a full new house are all hangs. The board choice still follows the room: Type X in the garage, cement board in the shower.

Text (208) 382-8431 with the rooms and the ceiling height to start the quote.