Bathroom Drywall in Meridian, Idaho

Meridian Quality Drywall hangs bathroom drywall in Meridian for full baths, powder rooms, and vanity walls after a supply leak. The wet zone is the point. Cement board in the shower. Moisture-resistant gypsum outside the spray. Regular white board does not belong in the surround.

Call (208) 382-8431 with the bath count, whether tile is going in the shower, and whether the bath is a first hang versus a wet-wall replacement.

Bathroom Drywall Options for Meridian Properties

Full bath, MR board throughout the dry walls

Moisture-resistant green or purple gypsum on walls that will take paint. 1/2-inch on 16-inch studs. Paper tape. A Level 4 finish unless enamel is the plan. The shower is a separate surround.

Shower and tub surround in cement board

HardieBacker or Durock on the studs in the spray. Joints taped with alkali-resistant mesh, not paper tape. We leave the surround ready for the tile trade. We do not hang paper-faced gypsum in the spray.

Powder room with no shower

A half bath can take regular board if the risk is only a sink. Behind the vanity we can still use MR board if a supply line has failed before. Texture to the hall so the powder room does not read as a different house.

Vanity back-wall after a supply leak

The plumber stops the water. We cut out soft board, dry the bay, and hang MR board on that wall. We do not skim over wet paper behind a vanity.

How We Handle Bathroom Drywall in Meridian

1. Map the wet zone. Shower, tub, and the rest of the room are different boards.
2. Confirm the leak is dead on replacements. Hang after the cavity is dry.
3. Hang cement board in the surround. Hang MR or regular on the dry walls.
4. Tape with the right tape: alkali-resistant mesh on cement board, paper on gypsum.
5. Finish the paint walls to the level the sheen needs. Leave the surround for tile.

Materials and Methods

ASTM C1396 moisture-resistant gypsum (green or purple) on wet-room walls outside the spray. Cement board in the surround. Alkali-resistant mesh on cement joints. Paper tape on gypsum. Setting compound on gypsum tape coats. The tile trade's thinset is not our joint compound. Screws rated for cement board in the surround. Regular drywall screws on the gypsum walls. Exhaust fans are an HVAC or electrical item. We cut the fan opening tight and mud to the housing. GA-216 for the gypsum hang. Manufacturer instructions for the cement board.

Hanging follows ASTM C840 on the gypsum walls. Joint compound and paper tape meet ASTM C475. GA-236 covers mud in a cold January shell or a July room over 100 F. Cement board stays in the spray. Moisture-resistant gypsum stays on the paint walls. Alkali-resistant mesh on the cement joints. Setting compound beds the gypsum tape. Exhaust housing cuts stay tight so the later coat does not crack.

Purple board and green board are both moisture-resistant gypsum. Neither is a shower backer. We say that on every bath quote because the wrong board in the surround is a tile failure later. Cement board in the spray. MR on the paint walls.

Exhaust fans get a tight cut and a housing we can mud to. A sloppy fan hole is a crack later. The fan itself is another trade. We coordinate the opening. We do not install the fan unless that is in the job in writing.

What Bathroom Drywall Costs in Meridian

Fixr puts a typical bath hang nationally around 430 to 500 dollars on their sample, with moisture-resistant board installed around one dollar sixty-five to two dollars seventy-five per square foot. Angi lists moisture-resistant material a bit above standard board. HomeAdvisor's water-resistant material band is about 55 to 70 cents per square foot for the sheet itself, plus labor. Tile, cement board area, and occupied-house protection shift a Meridian quote. We quote the bath as a wet-zone hang, not as a bedroom.

Tub surrounds on 2x4 walls need blocking for grab bars if those are in the plan. We add blocking before the cement board. Cutting cement board later to add a bar is a worse job. Say the bars when you call.

A bath on a second floor over a kitchen needs the lid below checked if the leak was a tub overflow. We hang the bath walls and we open the lid below if that field is soft. Two rooms can be one water event. We quote both if both are wet.

Niche blocking in a shower is easier before cement board than after. If a niche is in the tile plan, we frame it and board around it. Cutting a niche out of a finished surround is a worse cement-board job.

Bathroom Drywall Questions

Green board or cement board in a Meridian shower?

Cement board in the shower surround. Moisture-resistant gypsum on the other bath walls. Green or purple board is not a tile backer in the spray. Tile bond coats want cement board.

Can you hang a bath while the house is occupied?

Yes. We bag the hall, run a fan, and sequence coats. A small bath still needs dry time. Setting compound on the tape coat helps in this dry air.

What about a powder room with no shower?

A half bath can take regular board if the risk is only a sink. Behind the vanity we can still use MR board if a supply line has failed before. Texture to the hall so the powder room does not read as a different house.

Do you replace a vanity wall after a supply leak?

Yes after the plumber is done and the cavity is dry. Soft board comes out. MR board goes back on that wall. The rest of the bath only comes out if it is wet too.

Call (208) 382-8431 with the bath layout and whether tile is in the shower.